How To Identify
Your Signature RTL Round Pool Components

Learn how to identify the different components of your Signature RTL Round Pool.

Signature RTL Round Pool Model

Parts Breakdown

Identifying the parts of your pool model before you begin your installation will make the process of assembling the swimming pool much easier. Below you will find a complete breakdown of the parts and components for the Signature RTL Round Swimming Pool Model.

Top Ledge – Reference #6

Top Ledge

The Top Ledges (sometimes referred to as Top Rails) are the top finishing components of the swimming pool that are placed between the vertical upright posts. The Top Ledges are 7″ wide and are located at the very top of your pool.

Material: Resin

Ref #	Description	Part #	Length	12'
6	Top Ledge	22769	40-1/8"	11

Ref #	Description	Part #	Length	15'	18'	21'	24'	27'	30'
6	Top Ledge	22774	56-7/16"	10	12	14	16	18	20

Top Track/ Inner Stabilizer – Reference #1

Top Track

The Top Track Stabilizers are the tracks/rails that stabilize the top of the pool wall.

Material: Aluminum

Ref #	Description	Part #	Length	12'
1	Top Track (Inner Stabilizer)	10306	42-5/8"	11

Ref #	Description	Part #	Length	15'	18'	21'	24'	27'	30'
1	Top Track (Inner Stabilizer)	38502	53-1/4"	11
		10308	54-1/8"		13
		12903	54-7/16"			15
		10310	52-1/4"				18
		20163	52-7/8"					20
		19070	51-1/4"						23

Top Covers – Reference #9 & #10

Top Cover/Outer Cap

Top Cover/Inner Cap

The Top Caps consist of (2) parts. There is a Top Cover/Outer Cap which is closer to the outside of the pool. The Top Cover/Inner Cap is installed on the inside of the swimming pool closer to the water. The Top Caps cover all of the hardware where your Top Ledges screw into the Top Joiner Plates.

Ref #	Description	Part #	12'	15'	18'	21'	24'	27'	30'
9	Top Cover/Inner Cap	22732	11	10	12	14	16	18	20
10	Top Cover/Outer Cap	22734	11	10	12	14	16	18	20

Top Joiner Plate – Reference #3

Top Joiner Plate for Round & Oval Curved Side Cameo, Melenia, Heritage RTL & Signature RTL

Top Joiner Plate for Round & Oval Curved Side Uprights

The Top Joiner Plates are screwed in at the top of every Upright. Your swimming pool’s Top Ledges will be screwed into these Top Joiner Plates.

Ref #	Description	Part #	12'	15'	18'	21'	24'	27'	30'
3	Top Joiner Plate	22761	11	10	12	14	16	18	20

Uprights – Reference #5

Curved Side Upright

The Uprights are the vertical posts on the outside of your swimming pool wall. Each upright post inserts into the bottom upright boot and connects to the top joiner plate with screws.

Ref #	Description	Part #	12'	15'	18'	21'	24'	27'	30'
5	Upright	22760	11	10	12	14	16	18	20

Upright Boot – Reference #8

Upright Boot

The Upright Boots connect your Bottom Tracks together on a round pool and on the curved sides of an oval swimming pool. Your curved side uprights will also clip into the Upright boots.

Ref #	Description	Part #	12'	15'	18'	21'	24'	27'	30'
8	Upright Boot	22735	11	10	12	14	16	18	20

Coping Strips – Reference #7

Coping For Overlap Liners - 2ft. Section

Coping Strips

Overlap Liner Installation Using Coping Strips

An Overlap Pool Liner is installed by overlapping it over the pool wall and using plastic Coping Strips to hold it in place. Coping Strips are not required when installing a Uni-Bead Liner or J-Hook Liner, but they are included with the swimming pool. If using a Uni-Bead or J-Hook liner you can discard the coping strips.

Ref #	Description	Part #	12'	15'	18'	21'	24'	27'	30'
7	Coping Strips	10296	9	12	14	16	19	21	24

Bottom Track – Reference #2

Bottom Track

The Bottom Track (sometimes referred to as Bottom Rail) is where your pool wall sits.

The Bottom Track inserts into the Upright Boots on the curved sides of the swimming pool and Straight Side Bottom Rail Connector on the straight sides.