How To Identify
Your Saltwater 8000 Oval Pool Components

Learn how to identify the different components of your Saltwater 8000 Oval Pool.

How To Identify Your Saltwater 8000 Oval Pool Components
Saltwater 8000 Oval Pool Model

Saltwater 8000 Oval Pool Model

Parts Breakdown

Identifying the parts of your swimming pool before the installation process will make the installation a lot easier and go more smoothly. Below you will find a breakdown of the parts that are used on our Saltwater 8000 Oval Above Ground swimming pool and where they are used and installed.

Saltwater 8000 Parts Breakdown Round Section
Saltwater 8000 Parts Breakdown Straight Section

Top Ledge – Index #L & F

Saltwater 8000 Top Ledge

Top Ledge

The Top Ledges (sometimes referred to as Top Rails) are the top finishing components of the swimming pool that are placed between the vertical upright posts. The Top Ledges are 8″ wide and are located at the very top of your pool.

Material: Injected-molded Resin

Ref #DescriptionPart # Length 12'x16' 12'x18' 12'x20' 12'x24'
LTop Ledge (Straight Side) 10102350042 42" 26
2
4
FTop Ledge (Curved Side) 10102350000 56" 8
61010
Ref #DescriptionPart # Length 15'x26' 15'x30' 18'x33' 18'x40' 21'x43'
LTop Ledge (Straight Side) 10102350042 42" 46
61012
FTop Ledge (Curved Side) 10102350000 56" 121214
1414

Top Track – Index #A

Saltwater 8000 Top Track

Top Track

The Top Tracks (sometimes referred to as Inner Stabilizers) are the resin tracks that hold the liner onto the pool wall.

Material: Resin

Ref #DescriptionPart # Length 12'x16' 12'x18' 12'x20' 12'x24'
ATop Track (Straight Side) 10707000042 37" 26
2
4
Top Track (Curved Side) 1071507160000 56" 4
666
Top Track (Transition) 1071507160010 53-1/2" 4
4
4
Ref #DescriptionPart # Length 15'x26' 15'x30' 18'x33' 18'x40' 21'x43'
ATop Track (Straight Side) 10707000042 37" 46
61012
Top Track (Curved Side) 1071507160000 56" 8810
1010
Top Track (Transition) 1071507160010 53-1/2" 44
4
4
4

Top Caps – Index #G

saltwater-8000-top-outer-cap-650x650-small-dm_1125x1125.webp__PID:dfabd0f7-242a-4347-b923-282031021b25

Top Cap/Front Part

Top Cap/Back Part for Saltwater 8000 Pool Models

Top Cap/Back Part

The Top Caps consists of (2) parts. There is an Top Cap/Front Part which is closer to the outside of the pool. The Top Cap/Back Part is installed on the inside of the swimming pool closer to the water. The Top Caps cover all of the hardware where your Top Ledges screw into the Top Joiner Plates.

Ref #DescriptionPart # 12'x16' 12'x18' 12'x20' 12'x24'
GTop Cap/Front Part 10302350000 101212
14
Top Cap/Back Part 10302350010 1012
1214
Ref #DescriptionPart # 15'x26' 15'x30' 18'x33' 18'x40' 21'x43'
GTop Cap/Front Part 10302350000 161820
2426
Top Cap/Back Part 10302350010 16182024
26

Top Cap Cover Plate – Index #H

saltwater-8000-top-cover-plate-650x650-small-2-dm_1125x1125.webp__PID:a4113e40-28ee-41d8-8193-7539e7aaeac8

Top Cap Cover Plate

The Top Cap Cover Plates cover where the Top Caps screw into the Top Joiner Plate.

Ref #DescriptionPart # 12'x16' 12'x18' 12'x20' 12'x24'
HTop Cap Cover Plate 10302350030 101212
14
Ref #DescriptionPart # 15'x26' 15'x30' 18'x33' 18'x40' 21'x43'
HTop Cap Cover Plate 10302350030 161820
2426

Top Joiner Plate – Index #I

saltwater-8000-upright-top-joiner-650x650-small-2-dm_1125x1125.webp__PID:6d301bf2-61be-46fe-8c91-33278aaf27e2

Top Joiner Plate

The Top Joiner Plates are screwed in at the top of every Upright. Your swimming pool’s Top Ledges will be screwed into these Top Joiner Plates.

Ref #DescriptionPart # 12'x16' 12'x18' 12'x20' 12'x24'
ITop Joiner Plate 11102350000 101212
14
Ref #DescriptionPart # 15'x26' 15'x30' 18'x33' 18'x40' 21'x43'
ITop Joiner Plate 11102350000 161820
2426

Uprights – Index #E & R

saltwater-8000-curved-side-upright-650x650-small-dm_1125x1125.webp__PID:213dc775-fc9f-4b4a-a7e6-c0b6a0886714

Curved Side Upright

Straight Side Upright

Straight Side Upright

The Uprights are the vertical posts on the outside of your swimming pool wall.

For oval shaped swimming pools there are (2) types of Uprights. There are Uprights for the straight side and also the curved sides of the oval. They will differ slightly in shape as the straight side of an oval pool has different uprights than the curved sides. The Top Joiner plate will fit onto the top of the upright.

Ref #DescriptionPart # 12'x16' 12'x18' 12'x20' 12'x24'
ECurved Side Upright 10202350004 688
8
RStraight Side Upright 10004 44
44
Ref #DescriptionPart # 15'x26' 15'x30' 18'x33' 18'x40' 21'x43'
ECurved Side Upright 10202350004 101012
1212
RStraight Side Upright 10004 68812
14

Bottom Joiner Plate – Index #J

saltwater-8000-bottom-boot-joiner-650x650-small-dm_1125x1125.webp__PID:6795a864-2660-4ad4-8464-9b8dc43b7277

Bottom Joiner Plate

The Bottom Joiner Plates connect your Bottom Tracks together on a round pool and on the curved sides of an oval swimming pool. Your curved side uprights will also clip into the Bottom Joiner Plates.

Ref #DescriptionPart # 12'x16' 12'x18' 12'x20' 12'x24'
JBottom Joiner Plate 11202350000 688
8
Ref #DescriptionPart # 15'x26' 15'x30' 18'x33' 18'x40' 21'x43'
JBottom Joiner Plate 11202350000 101012
1212

Yardmore Gussets – Index #S

Left Side Gusset

Left Side Gusset

Right Side Gusset

Right Side Gusset

The Yardmore Gussets consists of a Left side and a Right Side that are attached together at each straight side Upright.

Ref #DescriptionPart # 12'x16' 12'x18' 12'x20' 12'x24'
SLeft Side Gusset 33090 444
6
SRight Side Gusset 33091 44
46
Ref #DescriptionPart # 15'x26' 15'x30' 18'x33' 18'x40' 21'x43'
SLeft Side Gusset 33090 688
1214
SRight Side Gusset 33091 68812
14

Channel Supports – Index #N & O

Top Channel Support Beam for Oval Wilbar & Saltwater Series Pool Models

Upper Oval Channel

Bottom Channel Support Beam for Oval Wilbar & Saltwater Series Pool Models

Under Ground Channel

The Upper (Top) Oval Channel and Under (Bottom) Ground Channel come together to form a tube. The Upper Oval Channel is longer than the Under Ground Channel and will extend past the Under Oval Channel towards the inside of the swimming pool.

The Gussets, Straight Side Uprights and Pressure Plates will be installed to these channels.

Ref #DescriptionPart # 12'x16' 12'x18' 12'x20' 12'x24'
NUpper Oval Channel 16539 444
6
OUnder Ground Channel 15933 44
46
Ref #DescriptionPart # 15'x26' 15'x30' 18'x33' 18'x40' 21'x43'
NUpper Oval Channel 16539 688
1214
OUnder Ground Channel 15933 68812
14

Pressure Plate – Index #M

Pressure Plate for Wilbar & Saltwater Series Oval Pool Models

Pressure Plate

The Pressure Plates are corrugated steel plates that attach to the Upper (Top) Oval Channels and to each other.

Ref #DescriptionPart # 12'x16' 12'x18' 12'x20' 12'x24'
MPressure Plate 16549 444
6
Ref #DescriptionPart # 15'x26' 15'x30' 18'x33' 18'x40' 21'x43'
MPressure Plate 16549 688
1214

Bottom Straight Side Track Connector – Index #T

saltwater-8000-straight-side-connector-650x650-small-dm_1125x1125.webp__PID:43af6212-f639-4ddb-a12d-7c95114b050d

Bottom Straight Side Track Connector

The Connector Bottom Rail Straight Side attaches to the Upper (Top) Oval Channel and is used to connect the straight side Bottom Tracks. The straight side Bottom Tracks will slide into the Connector on both sides.

Ref #DescriptionPart # 12'x16' 12'x18' 12'x20' 12'x24'
TBottom Straight Side Track Connector 10402000000 444
6
Ref #DescriptionPart # 15'x26' 15'x30' 18'x33' 18'x40' 21'x43'
TBottom Straight Side Track Connector 10402000000 688
1214

Bottom Track – Index #B

Saltwater 8000 Bottom Track

Bottom Track

The Bottom Track (sometimes referred to as Bottom Rail) is where your pool wall sits.

The Bottom Track inserts into the Bottom Joiner Plates on the curved sides of the swimming pool and Bottom Straight Side Track Connector on the straight sides.

Material: Resin

Ref #DescriptionPart # Length 12'x16' 12'x18' 12'x20' 12'x24'
BBottom Track Straight Side 10807000042 37" 26
2
4
Bottom Track Transition Left 1081507000030 53-1/2" 2
22
Bottom Track Transition Right 1081507000020 53-1/2" 2
2
2
Bottom Track Curved Side 1081507000000 56" 4 6
66
Ref #DescriptionPart # Length 15'x26' 15'x30' 18'x33' 18'x40' 21'x43'
BBottom Track Straight Side 10807000042 37" 46
61012
Bottom Track Transition Left 1081507000030 53-1/2" 222
2
Bottom Track Transition Right 1081507000020 53-1/2" 22
2
2

Bottom Track Curved Side 1081507000000 56" 88
1010
Bottom Track Transition Left 2082407000030 53-1/2"

2
Bottom Track Transition Right 108240700002053-1/2" 2
Bottom Track Curved Side 108240700000056" 10

Strap Section – Index #P

Saltwater 8000 Strap Section

Strap Section

The Strap Sections are connected to the Upper (Top) Oval Channels and lay flat across the width of our Oval Swimming Pools.

Ref #DescriptionPart # Length 12'x16' 12'x18' 12'x20' 12'x24'
PStrap Section 16724 41-11/16" 44
4
6
Ref #DescriptionPart # Length 15'x26' 15'x30' 18'x33' 18'x40' 21'x43'
PStrap Section 16725 40-11/16" 912
16726 52-11/16" 12
18
22126 49"


28

Oval Channel End Cap – Index #W

Top Channel End Cap for Oval Wilbar & Saltwater Series Pool Models

Oval Channel End Cap

The Oval Channel End Cap is installed on the Upper (Top) Oval Channel and is used to prevent dirt and sand from entering the Channel.

Ref #DescriptionPart # 12'x16' 12'x18' 12'x20' 12'x24'
WOval Channel End Cap 22726 444
6
Ref #DescriptionPart # 15'x26' 15'x30' 18'x33' 18'x40' 21'x43'
WOval Channel End Cap 22726 688
1214

3 Hole Square Washers – Index #Q

3-Hole Square Washers for Oval Wilbar & Saltwater Series Pool Models - Set of 2

3 Hole Square Washers

The 3 Hole Square Washers are used in the pre-assembling of the straight sides of a buttress-free oval pool.

The 3 Hole Square Washers are installed on each side of the supports when joining the Gussets, Under (Bottom) Ground Channel, Upper (Top) Oval Channel and Straight Side Uprights together.

Ref #DescriptionPart # 12'x16' 12'x18' 12'x20' 12'x24'
Q3 Hole Square Washers 16663 888
12
Ref #DescriptionPart # 15'x26' 15'x30' 18'x33' 18'x40' 21'x43'
Q3 Hole Square Washers 16663 121616
2428

Foam Block

Foam Block for Top Channel Beam - Fits Wilbar & Saltwater Series Oval Pools

Foam Block

The Foam Blocks are inserted into the Upper (Top) Oval Channel towards the inside of the pool. The Foam Blocks are used to prevent voids (sink holes) from forming at the location of the channels.

Coping Strips – Only Included with Overlap Liners

Coping For Overlap Liners - 2ft. Section

Coping Strips

Coping For Overlap Liners - 2ft. Section

Overlap Liner Installation Using Coping Strips

An Overlap Pool Liner is installed by overlapping it over the pool wall and using plastic Coping Strips to hold it in place. Coping Strips are not required when installing a Uni-Bead Liner or J-Hook Liner.

Click on the tab below to view the Manufacturer’s Installation and Safety Instructions for the Saltwater 8000 Oval Swimming Pool.

SALTWATER 8000 OVAL INSTALLATION & SAFETY INSTRUCTIONS

Saltwater 8000 Replacement Parts

Need a replacement part? Shop our selection of Saltwater 8000 Pool Parts by clicking on the tab below:

Shop Products
Top Cap/Back Part for Saltwater 8000 Pool Models