How To Identify
Your Saltwater 5000 Oval Pool Components

Learn how to identify the different components of your Saltwater 5000 Oval Pool.

Saltwater 5000 Oval Pool Model

Parts Breakdown

Identifying the parts of your pool model before you begin your installation will make the process of assembling the swimming pool much easier. Below you will find a complete breakdown of the parts and components for the Saltwater 5000 Oval Swimming Pool Model.

Top Rail – Reference #6

Top Rail

The Top Ledges (sometimes referred to as Top Rails) are the top finishing components of the swimming pool that are placed between the vertical upright posts. The Top Ledges are 7″ wide and are located at the very top of your pool.

Material: Resin

Ref #	Description	Part #	Length	12'x24'	15'x24'	15'x30'	18'x33'	18'x40'
6	Top Ledge	22769	40-1/8"	10
		22770	51-1/16"		10	10
		22771	51-13/16"				12	12
		22775	41-1/8"	8	2	10	10	14
		29762	47-1/4"		4

Inner Stabilizer – Reference #1

Inner Stabilizer

The Inner Stabilizers (sometimes referred to as Top Track Stabilizers) are the tracks that stabilize the top of the pool wall.

Material: Resin

Ref #	Description	Part #	Length	12'x24'	15'x24'	15'x30'	18'x33'	18'x40'
1	Inner Stabilizer	29934	8"	6	4	8	8	12
		29935	33"	4	2	6	6	10
		29936	37"	4		4	4	4
		33129	40-1/4"	10
		37422	43"		4
		29890	56-1/16"				12	12
		11428	51-1/16"		10	10

Top Caps – Reference #9 & #10

Top Cap/Outer Cap

Top Cover/Inner Cap for Cameo, Heritage RTL, Signature RTL & Saltwater 5000

Top Cap/Inner Cap

The Top Caps consists of (2) parts. There is an Outer Cap Top Cap which is closer to the outside of the pool. The Inner Cap Top Cap is installed on the inside of the swimming pool closer to the water. The Top Caps cover all of the hardware where your Top Ledges screw into the Top Joiner Plates.

Usually for oval shaped swimming pools there are (2) types of Outer Cap Top Caps. There are Outer Caps for the straight side and also the curved sides of the oval. They will differ slightly in shape as the straight side of an oval pool has different uprights than the curved sides and the cap must fit onto the upright.

Ref #	Description	Part #	12'x24'	15'x24'	15'x30'	18'x33'	18'x40'
9	Top Cover/Inner Cap	22734	18	16	20	22	26
10	Top Cover/Outer Cap - Straight Side	22733	6	4	8	8	12
10	Top Cover/Outer Cap - Curved Side	22732	12	12	12	14	14

Top Plates – Reference #3 & #13

pool-supplies_replacement-parts-650x650-00009-dm_1125x1125.webp__PID:9a03d851-395e-4b56-b751-c8296cdb62e1

Top Plate Curved Side

pool-supplies_replacement-parts-650x650-00010-dm_1125x1125.webp__PID:d851395e-ab56-4751-8829-6cdb62e1a3f9

Top Plate Straight Side

The Top Joiner Plates are screwed in at the top of every Upright. Your swimming pool’s Top Ledges will be screwed into these Top Joiner Plates.

For oval shaped swimming pools there are (2) types of Top Joiner Plates. There are Top Joiner Plates for the straight side and also the curved sides of the oval. They will differ slightly in shape as the straight side of an oval pool has different uprights than the curved sides and the Top Joiner plate must fit onto the top of the upright.

Ref #	Description	Part #	12'x24'	15'x24'	15'x30'	18'x33'	18'x40'
3	Top Joiner Plate Curved Side	38908	12	12	12	14	14
13	Top Joiner Plate Straight Side	38911	6	4	8	8	12

Uprights – Reference #5 & #14

Upright

Upright Oval Straight Side

The Uprights are the vertical posts on the outside of your swimming pool wall. Each upright post on the curved side of the swimming pool inserts into the bottom upright boot and connects to the top joiner plate with screws.

For oval shaped swimming pools there are (2) types of Uprights. There are Uprights for the straight side and also the curved sides of the oval. They will differ slightly in shape as the straight side of an oval pool has different uprights than the curved sides and the Top Joiner plate must fit onto the top of the upright.

Ref #	Description	Part #	12'x24'	15'x24'	15'x30'	18'x33'	18'x40'
5	Curved Side Uprights	22759	12	12	12	14	14
14	Straight Side Uprights	35738	6	4	8	8	12

Boot – Reference #8

Boot

The Upright Boots connect your Bottom Tracks together on the curved sides of an oval swimming pool. Your curved side uprights will also clip into the Upright boots.

Ref #	Description	Part #	12'x24'	15'x24'	15'x30'	18'x33'	18'x40'
8	Boots	22735	12	12	12	14	14

Coping Strips – Reference #7

Coping For Overlap Liners - 2ft. Section

Coping Strips

Overlap Liner Installation Using Coping Strips

An Overlap Pool Liner is installed by overlapping it over the pool wall and using plastic Coping Strips to hold it in place. Coping Strips are not required when installing a Uni-Bead Liner or J-Hook Liner, but they are included with the swimming pool. If using a Uni-Bead or J-Hook liner you can discard the coping strips.

Ref #	Description	Part #	Length	12'x24'	15'x24'	15'x30'	18'x33'	18'x40'
7	Coping Strips	10296	48"	16	19	19	21	24

Yardmore Gussets – Reference #15 & #16

Yardmore Gusset Left

Yardmore Gusset Right

The Yardmore Gussets consists of a Left side and a Right Side that are attached together at each straight side Upright.

Ref #	Description	Part #	12'x24'	15'x24'	15'x30'	18'x33'	18'x40'
15	Left Side Gusset	35740	4	4	8	8	12
16	Right Side Gusset	35741	4	4	8	8	12

Channel Supports – Reference #18 & #19

Top Channel Support Beam for Oval Wilbar & Saltwater Series Pool Models

Upper Oval Channel

Bottom Channel Support Beam for Oval Wilbar & Saltwater Series Pool Models

Under Ground Channel

The Upper (Top) Oval Channel and Under (Bottom) Ground Channel come together to form a tube. The Upper Oval Channel is longer than the Under Ground Channel and will extend past the Under Oval Channel towards the inside of the swimming pool.

The Gussets, Straight Side Uprights and Pressure Plates will be installed to these channels.

Ref #	Description	Part #	Length	12'x24'	15'x24'	15'x30'	18'x33'	18'x40'
18	Upper Oval Channel	16539	52-3/8"	6	4	8	8	12
19	Under Ground Channel	15933	45-9/16"	6	4	8	8	12

Pressure Plate – Reference #21

Pressure Plate

The Pressure Plates are corrugated steel plates that attach to the Upper Oval Channels and to each other.

Ref #	Description	Part #	12'x24'	15'x24'	15'x30'	18'x33'	18'x40'
21	Pressure Plate	16549	6	4	8	8	12

Connector Bottom Rail Straight Side – Reference #17

Bottom Straight Side Track/Rail Connector for Oval Wilbar Pool Models

Connector Bottom Rail Straight Side

The Straight Side Bottom Rail Connector attaches to the Upper (Top) Oval Channel and is used to connect the straight side Bottom Tracks. The straight side Bottom Tracks will slide into the Connector on both sides.

Ref #	Description	Part #	12'x24'	15'x24'	15'x30'	18'x33'	18'x40'
17	Straight Side Bottom Rail Connector	16542	6	4	8	8	12

Bottom Rail – Reference #2

Bottom Track

The Bottom Track (sometimes referred to as Bottom Rail) is where your pool wall sits.

The Bottom Track inserts into the Upright Boots on the curved sides of the swimming pool and Straight Side Bottom Rail Connector on the straight sides.

Material: Resin

Ref #	Description	Part #	Length	12'x24'	15'x24'	15'x30'	18'x33'	18'x40'
2	Bottom Track	12311	49"		10	10		12
		12327	37-1/2"	4	2	6	6	10
		12328	39"	4		4	4	4
		12330	45"		4
		12331	50"				12
		38991	38"	10				12

Strap Section – Reference #22

Strap Section

The Strap Sections are connected to the Upper (Top) Oval Channels and lay flat across the width of our Oval Swimming Pools.

Ref #	Description	Part #	Length	12'x24'	15'x24'	15'x30'	18'x33'	18'x40'
22	Strap Section	16724	41-11/16"	6
		16725	40-11/16"		6	12
		16726	52-11/16"				12	18

Oval Channel End Cap – Reference #23

Top Channel End Cap for Oval Wilbar & Saltwater Series Pool Models

Oval Channel End Cap

The Oval Channel End Cap is installed on the Upper (Top) Oval Channel and is used to prevent dirt and sand from entering the Channel.

Ref #	Description	Part #	12'x24'	15'x24'	15'x30'	18'x33'	18'x40'
23	Channel End Cap	22726	6	4	8	8	12

3 Hole Square Washers – Reference #20

3 Hole Square Washers

The 3 Hole Square Washers are used in the pre-assembling of the straight sides of a buttress-free oval pool.

The 3 Hole Square Washers are installed on each side of the supports when joining the Gussets, Under (Bottom) Ground Channel, Upper (Top) Oval Channel and Straight Side Uprights together.

Ref #	Description	Part #	12'x24'	15'x24'	15'x30'	18'x33'	18'x40'
20	3 Hole Square Washers	16663	12	8	16	16	24

Foam Block – Reference #24

Foam Block

The Foam Blocks are inserted into the Under (Bottom) Ground Channel. Foam Blocks are used to prevent sand from entering the Under (Bottom) Ground Channel.